Urinal Cistern Refill Frequency Flush Controls

Battery Powered PIR Sensor Flow Control kit for urinal cisterns, everything you need in one box.

Maintains hygiene standards whilst conserving water and dramatically cutting water costs – saving up to 95% of water usage compared with an uncontrolled cistern, and around 30-40% against more basic water management systems.
The Flow Saver consists of an electronic control sensor unit and a solenoid for installation into the water supply pipe of a urinal auto cistern. The unit monitors washroom traffic to schedule cistern flushes. Where no motion is detected a hygiene flush is initiated at 12 hour intervals. During high usage periods where the number of detections exceeds 20, the unit will temporally switch from 30 or 60 minute flushing to 15 minute flushing for improved hygiene.

Features:
•    Anti-Vandal Polycarbonate Domed Housing
•    Test Cycle Function
•    Easy Setup with LED Status Indicator and Beeper
•    Battery Powered
•    Low Battery Warning Light
•    Tamper Proof Cover With Key
•    Wall or Ceiling Mounted
•    High Quality WRAS Approved ASCO Latching Solenoid Valve

Kit Includes:
- Flush controller unit with sensor eye for wall or ceiling mount above the urinals
- Asco solenoid valve for fitting to water supply (15mm compression fit)
- Approx. 1m of  two core cable to connect controller to solenoid
- Cover release key
- Fixing plugs and screws
- 4 x AA  LR6 Alkaline Batteries

Specification:
Construction: ABS/PC
Sensor range: 3 metres
Motion sensor: Passive Infra-Red (PIR) 
Water control: Asco DC latching 2.0mm orifice solenoid valve
Water Pressure: 0.5 - 7.0 BAR
Power: 4 x AA Battery cells (LR6)
Typical Battery Life: Alkaline batteries (supplied) 12-18 months, Lithium batteries (not supplied) 2-3 years
Dimensions: 130 x 130 x 45mm

Click on the Product Data Sheets tab for downloadable instructions and data sheets.

A wide-angle PIR sensor manufactured by Marnic Technologies, in an enamel painted steel case. Many thousands of this inexpensive, yet high-quality, controller have been supplied to Gentworks customers. They are very popular with schools and local authority sites as well as pubs, offices and factories. 

Can be calibrated to flush up to 4 times per hour but we recommend it is set to flush 20 minutes after the sensor detects a user, therefore a maximum of 3 times per hour. If no user is detected (e.g. over weekends), there is a choice of flushing after 12 or 24 hours. 

The solenoid can be installed on either vertical or horizontal pipe. An arrow on the brass body indicates the direction of flow.

Includes:
- Flush controller box with sensor eye for wall or ceiling mount above the urinals
- Marnic Solenoid valve for fitting to water supply (15mm compression fit)
- Approx 1m of 2 core cable to connect controller to solenoid
- 4.5v Alkaline Duracell battery with tails (Battery version only)
- 240v to 4.5v Built in Power Supply (PSU) (Mains version only)

Click on the Product Data Sheets tab for downloadable instructions and data sheets. 

One of the original flush controllers from 25 years ago, this Cistermiser works by sensing the drop in water pressure caused by hand washing.
No electronics, no sensors. They are still chosen by some, nevertheless.

This model is for use with:
- Mains water or tank-fed systems above 5 metres head
- Operating sensitivity is 10% of supply pressure

Includes:
- Flush controller unit for compression fit to cistern water feed.

Features:
- Up to 80% savings on water costs
- Reliable and low maintenance
- Water pressure sensor for detecting bathroom occupancy
- Adjustable fill time
- Adjustable operating sensitivity
- WRAS approved product

How it works
The Cistermiser hydraulic valve is installed on the supply pipe to the urinal cistern.
The valve is activated by short-term pressure drops created by use of taps or WCs on the same supply.
The valve is normally closed; when it is activated it opens and water passes to the urinal cistern until the pressures on both sides of the valve are equalised.
When the cistern is full the auto-siphon will flush.

Installation instructions for Cistermiser hydraulic valves. 

This Low Flush controller can initiate a flush every 1-15 hours so that the standing water in the cistern and flush pipes will be regularly 'purged', thus usually avoiding the need to carry out a dead-leg procedure to minimise the risk of legionella.

           'FCV01 / UC01-010/011 Low flush Timer' Instruction Manual

 

This compact PIR flush controller, manufactured by Dart Valley Systems, incorporates the electronics and settings panel in this ceiling mounted sensor unit. Perfect for washrooms with false ceilings. Very reliable, easy to calibrate with excellent flexibility in flush and cistern fill times.

Includes:
- Solenoid valve for connection to water supply (15mm compression fit)

- Sensor, incorporating flush controller system, for fitting into ceiling above urinals

- 6v lithium battery (Duracell 223 (CR-P2) or similar) or power transformer depending on power option chosen

Features:
- Up to 80% savings on water costs
- Extremely reliable and low maintenance
- Passive infra-red sensor, occupancy detection
- Low power consumption - typical battery life of 2-4 years (battery model)
- Single battery input (battery model)
- Single valve output
- Default pre-set settings
- Valve open button
- Adjustable cistern fill time (15 mins max)
- Adjustable delay time after sensor triggered (30 mins max)
- Janitorial flush (if sensor not triggered for 12 hours)

        Pearl Downlighter (cistern fill model) Instruction Manual

 

The Flushmatic from KWC DVS (formerly Dart Valley Systems) is one of the most reliable flush controllers available. The controller box incorporates a sensor to detect urinal usage. It is simple to install and calibrate. Product Codes: UC01-011 / UC01-014 (formerly D114/D124)

Includes:
- Flush controller box to affix to wall
- Solenoid valve for connection to water supply
- 6v lithium battery or power transformer depending on chosen option

Features:
- Up to 80% savings on water costs
- Extremely reliable and low maintenance
- Passive infra-red sensor, occupancy detection
- Low power consumption - typical battery life between 3 and 5 years (battery model)
- Single battery input (battery model)
- Single valve output
- Default preset settings
- Adjustable cistern fill time (15 mins max)
- Adjustable delay time after sensor triggered (30 mins max)
- Janitorial flush (if sensor not triggered for 12 hours) 

            Flushmatic Instruction Manual

Click here to view ALL MAKES of PIR sensor urinal flush controllers

The IRC has the advantage of being packaged for installation onto a wall, recessed into a false ceiling or directly onto the water supply pipe. The included solenoid valve is plumbed into the water supply to the urinal cistern. The connection to the control sensor box can be made by mounting the box directly onto the solenoid valve or remote from the valve, using the 'floating socket'.

Features:
- reduced water consumption by up to 80%
- reliable and low maintenance
- passive infra-red sensor, occupancy detection
- single valve output
- adjustable flow rate
- janitorial flush (if sensor not triggered for 12 hours)
- WRAS approved Product